Huatao Group

Huatao Group

Home> Company News> Installation Steps and Precautions for Precision Security Filters

Installation Steps and Precautions for Precision Security Filters

October 18, 2024
I. Installation Steps
 
1. Thoroughly clean the filter housing.
2. The inlet and outlet of the housing are connected to the pipeline of the filtration system. Pay attention to the direction when connecting to ensure that the filter element is in the state of water inlet from the outside and water outlet from the inside.
3. Open the plastic bag at one end of the filter element opening and check whether the O-ring is intact and in place.
 
4. Wet the O-ring and the filter element seat jack with a suitable wetting agent (such as water).
5. Hold the end of the filter element close to the O-ring and vertically insert the filter element socket into the filter element seat jack.
6. After all the filter elements are inserted, remove the filter element packaging bag, then buckle the pressure plate to fix it, and then install the upper head.
7. Open the bleed valve on the top of the housing.
 
Regarding  Filters  Liquid Filtration,Precision Filter,Precision Security Filters,Automatic Filter,Scraper Self-cleaning Filter, Multi Media Filter,Quartz Sand Filter,Ultra Precision Filter,Cartridge Filter And Parts.
 
8. Slightly open the inlet valve to allow liquid to enter the housing until the liquid overflows from the bleed valve on the top of the housing. At this time, close the bleed valve.
9. Slowly adjust and open the downstream outlet valve until it is fully opened.
10. Slowly adjust and open the inlet valve until it is fully opened. At this time, the pressure drop between the upstream and downstream of the filter is 0.02Mpa (determine the initial pressure drop under the flow rate).
 
II.Precautions for Use
 
1. Prevent pressure shock during operation and prohibit reverse pressurization.
2. When the pressure drop between the upstream and downstream of the filter is greater than 0.3Mpa or the flow rate drops significantly, consider replacing the filter element.
 
3. If the filter is not working temporarily, do not dry the filter element, but soak it in a suitable sterilization solution (or inject such a solution into the shell), and rinse the sterilization solution before reuse.
 
4. If the filter is steam sterilized, the condensed water in the steam pipeline must be drained first, and the steam pressure should not exceed 0.1Mpa. At the same time, the pressure drop between the upstream and downstream of the filter should not exceed 0.015Mpa. If the wet filter element is steam sterilized, the liquid absorbed by the filter element should be drained with clean compressed air before passing the steam, otherwise the filter element will be damaged when the steam is passed.
 
 
Contact Us

Author:

Ms. Janet Wang

Phone/WhatsApp:

+8617736903537

Popular Products
You may also like
Related Information
How to Install And Use Shallow Sand Filter

Operation sequence of shallow sand filter: (1) Shallow sand filter starts filtering. Close the filter inlet valve and filter outlet valve respectively. Open the filter bypass valve, wait for water to...

Precautions for Shallow Sand Filter Operation

Precautions for shallow sand filter operation and maintenance guide: Preparation before starting: Operators must hold an operation card and be operated by a dedicated person. If there are obstacles...

Safety Precautions During the Use of Shallow Sand Filter

(1) Users of shallow sand filter must use and inspect it in accordance with regulations. (2) During the operation of the equipment, unauthorized personnel must not approach the equipment. (3) During...

Replacement cycle of Precision Security Filters Element

There is no fixed time for how often the filter element of the security filter should be replaced. It mainly depends on the actual use. When the water quality decreases significantly, the filter...

Related Categories

Email to this supplier

Subject:
Email:
Message:

Your message must be betwwen 20-8000 characters

  • Tel:

    86-0311-80690567

  • Mobile:

    +8617736903537

  • Email:

    janet.wang@huataogroup.com

  • Address:

    No.298 Zhonghua North Street,Xinhua District, Shijiazhuang, Hebei China

  • Follow us:

NEWSLETTER

Sign up for industry alerts, our latest news. thoughts, and insights from Huatao Group.

Copyright © 2024 Huatao Group All rights reserved. Privacy Policy
We will contact you immediately

Fill in more information so that we can get in touch with you faster

Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.

Send